Name: SPC Herringbone parquet, white oak look, 12.6×63 cm, thickness 5 mm
Brand: MallDeco
Price: 52.84 EUR
Availability: InStock

Box contents

Commercialization

Design

Integrated underlay

Plank size

Set contents

Surface

Wear layer

Thickness/Weight

Characteristics

SPC Flooring

Herringbone Flooring

SPC Herringbone parquet with a white oak look, designed for bright, elegant and durable interiors.

Each board is 12.6×63 cm in size and 5 mm thick. The surface is provided with a 0.5 mm wear layer, and the integrated 1 mm IXPE support contributes to comfort in use and reduced noise when walking.

&nbsp;

Sales information:

The product is sold in a set consisting of two boxes: box A + box B. Each box contains 14 tiles, and the complete set contains 28 tiles, necessary for the herringbone pattern installation,&nbsp;with a total covered area of ~ 2.22&nbsp;m².

&nbsp;

Color note:

Product colors may vary slightly depending on the screen on which the images are viewed, its settings and ambient brightness.

The first and perhaps the most important step in ordering a wallpaper model is measuring the wall. We recommend adding 10 cm to each height for more effectiveness and safety.

For an ordinary wall, the process should be simple and intuitive: measure the length and height of the wall separately and note the respective elevations. Avoid including decorative elements such as plinths, battens, or other such accessories in the measurements. Check the measurements. 
With an inclined wall, it is important to start with the longer or wider side, with increased attention to any kind of irregularity or unevenness of the wall. The wallpaper roll has a rectangular shape, which means that during assembly it can be cut or cut according to the respective shape and specifications. 
If you have an irregular wall&nbsp;or one that frames elements such as a window, door, or something similar, we recommend measuring the total dimensions of the wall. During installation, all these elements will be cut from the wallpaper roll.

 
Important! For any measurements, we recommend adding 10 cm to avoid any error or imperfection of the wall!

Carefully prepare the surface on which the wallpaper is to be glued. It must be clean, neat, and non-absorbent. If you want to apply it on a new screed or plasterboard, apply a primer based on an race first. The mounting surface must be white.

The wallpaper strips are cut taking care of the continuity of the model, numbering them on the back with a pencil (no pen is used), then the strip is glued following the vertical or the previously glued strip. Prepare the adhesive according to the type of wallpaper. Mix the contents with water until a homogeneous paste is obtained. Mix vigorously again after 5 minutes. With a stencil or a brush, apply an even layer on the wall, or, as the case may be, on the wallpaper roll. Always follow the instructions for use of the wallpaper manufacturer. Immediately clean the excess adhesive with a damp cloth.

It is pressed with a rubber roller or squeegee, taking care not to leave air bubbles under the wallpaper, after which immediately wipe off the excess adhesive from the joints. Do not rub the joints hard! When it is wet, the wallpaper is more sensitive and can be damaged very easily.

If you have purchased a paintable vinyl wallpaper, allow at least 24 hours to pass between gluing the wallpaper and applying the first layer of paint. The paint must be water-based.

High-quality wallpaper can create a pleasant and welcoming interior. In order to prolong the life of the wallpaper, it must be vacuumed and wiped, if necessary, with a damp cloth, soaked in an ecological solution, without additives.

Measuring the wall

Preparing the wall

Installation of wallpaper

Recommendation

SPC Herringbone parquet, white oak look, 12.6×63 cm, thickness 5 mm

MallDeco

SuperPrice – Marks a product whose price is competitive compared to relevant online offers. Valid from DD.MM.YYYY to DD.MM.YYYY.

Calculate how many wallpaper rolls you need

To any measurement, we recommend adding 10 cm to avoid any error or imperfection of the wall!

Enter dimensions and options

according to the dimensions you entered, and the price below is for the number of rolls needed for the indicated area.

Calculate how many packs you need

We deliver the products directly to your door

Free shipping for orders over 16000 eur. Guaranteed return within 14 days

 Please notify me when it's back in stock

Share your opinion by giving a rating to the product.

Other customers have also seen the displayed products

By sending the request, you agree with the

By publishing the review, you agree with the

SPC Herringbone parquet, white oak look, 12.6×63 cm, thickness 5 mm

Products from the same collection

Recommended products

Box contents	14 planks
Commercialization	Set consisting of Box A + Box B
Design	Wood
Integrated underlay	1 mm IXPE foam
Plank size	12,6 × 63 cm
Set contents	28 planks
Surface	~ 2,22 m²
Wear layer	0,5 mm
Thickness/Weight	5 mm